Đồng hồ nhiệt độ 48x48mm ngõ ra rơ-le ACS-13A-R/M, AC100-240

(OUT1)

Option

Thermocouple

－2000 to 10000

SV display———– 11-segment Backlight LCD Green, Character size, 6.0 x 3.5mm (H x W)

MEMO display—— 11-segment Backlight LCD Green, Character size, 4.8 x 2.8mm (H x W)

Indicators————- Backlight Orange

Input

Direct current——- 0 to 20 mA DC, 4 to 20 mA DC: Input impedance: 50Ω , Allowable input current: 50 mA DC max.

DC voltage———– 0 to 1 V DC: Input impedance 1 MΩ min.

Allowable input voltage: 5 V DC max. Allowable signal source resistance: 2 kΩ max.

0 to 5 V DC, 1 to 5 V DC, 0 to 10 V DC: Input impedance: 100 kΩ min. Allowable input voltage: 15 V DC max.

Allowable signal source resistance: 100Ω max.

Accuracy (Setting・Indication)

However, R, S input, the range is 0 to 200℃ (32 to 392°F): Within ±6℃ (12°F) B input, the range is 0 to 300℃ (32 to 572°F): The accuracy is not guaranteed. K, J, E, T, N input, less than 0℃ (32°F): Within ±0.4% of input span ±1digit

RTD—————————– Within ±0.1% of each input span±1digit, or within ±1℃ (2°F), whichever is greater

Direct current, DC voltage — Within ±0.2% of each input span±1digit

Non-contact voltage — 12 V DC ±15% Max. 40 mA DC (short circuit protected)

Direct current ———– 4 to 20 mA DC Load resistance: Max. 550Ω

Control action

PID (with auto-tuning function), PI, PD (with auto-reset function), P (with auto-reset function), ON/OFF

OUT1 proportional band (P)———- 0 to 1000℃ (2000°F), 0.0 to 1000.0℃ (1999.9°F), or 0.0 to 100.0%(ON/OFF control when set to 0 or 0.0)

Integral time (I)—————————- 0 to 1000 seconds (OFF when set to 0)

Derivative time (D)———————– 0 to 300 seconds (OFF when set to 0)

OUT1 ON/OFF action—————— When the proportional band is set to 0 or 0.0

OUT1 proportional cycle————— 1 to 120 seconds (Not available for Direct current output type)

ARW——————————————- 0 to 100%

OUT1 ON/OFF action hysteresis — 0.1 to 100.0℃ (°F) or 1 to 1000 OUT1 high limit————————— 0 to 100% (Direct current: -5 to 105%)

OUT1 low limit—————————– 0 to 100% (Direct current: -5 to 105%)

Alarm 1 output

・No alarm action

・High limit alarm                           (Deviation setting) Setting range: －(Input span) to Input span

・Low limit alarm                            (Deviation setting) Setting range: －(Input span) to Input span

・High/Low limits alarm                  (Deviation setting) Setting range: 0 to Input span

・High/Low limit range alarm           (Deviation setting) Setting range: 0 to Input span

・Process high alarm                                                  Setting range: Input range low limit value to Input range high limit value

・Process low alarm                                                   Setting range: Input range low limit value to Input range high limit value

・High limit with standby alarm        (Deviation setting) Setting range: －(Input span) to Input span

・Low limit with standby alarm         (Deviation setting) Setting range: －(Input span) to Input span

・High/Low limits with standby alarm (Deviation setting) Setting range: 0 to Input span Setting accuracy——- Same as indication accuracy

Action——————— ON/OFF action

Hysteresis————– 0.1 to 100.0℃ (°F) or 1 to 1000

Output——————— Relay contact 1a, Control capacity: 3 A 250 V AC (Resistive load), Electrical life: 100,000 cycles

24 V AC/DC 50/60 Hz (Allowable voltage fluctuation range: 20 to 28 V AC/DC)

Input error indication, Indication range, Control range, Warm-up indication, Auto/Manual control switching, Console communication

CT (Current transformer): CTL-6-S-H: 1 piece [W (20A) option],      CTL-12-S36-10L1U: 1 piece [W (50A) option]

CTL-6-S-H: 2 pieces [W3 (20A) option], CTL-12-S36-10L1U: 2 pieces [W3 (50A) option]

This option and Heater burnout alarm (W, W3 option) utilize common output terminals.

Heater burnout alarm [W, W3 option] (CT included)

Must be specified.

Setting range———- Rated current 20 A [W(20A), W3(20A)]: 0.0 to 20.0 A

Rated current 50 A [W(50A), W3(50A)]: 0.0 to 50.0 A Setting accuracy—– Within ±5% of the rated value

Action——————– ON/OFF action

Output——————– Relay contact 1a, Control capacity: 3A 250V AC (resistive load), Electrical life: 100,000 cycles

If this option is ordered, Heating/Cooling control (D□ option) cannot be ordered.

Heating/Cooling control

OUT2 proportional band (P) — 0.0 to 10.0 times OUT1 proportional band (ON/OFF action when set to 0.0) OUT2 integral time (I)————- Same as that of OUT1

OUT2 derivative time (D)——– Same as that of OUT1

OUT2 proportional cycle——— 1 to 120 seconds

Overlap/Dead band—————- Thermocouple, RTD: -100.0 to 100.0℃ (°F)

Direct current, voltage: -1000 to 1000 (The placement of the decimal point follows the selection.) OUT2 hysteresis ——————- 0.1 to 100.0℃ (°F), or 1 to 1000

OUT2 cooling method————- One cooling method can be selected from Air cooling (linear characteristic), Oil cooling (1.5th power of the

linear characteristic) and Water cooling (2nd power of the linear characteristic) by keypad.

Output———————————- Relay contact 1a, Control capacity: 3A 250V AC (resistive load), Electrical life: 100,000 cycles

Non-contact voltage 12 V DC±15% Max. 40 mA DC (short circuit protected)

If this option is ordered, Alarm 2 (A2 option) and Heater burnout alarm (W, W3 option) cannot be ordered.

Serial communication [C5 option]

Communication line—————— EIA RS-485

Communication method————- Half-duplex communication

Synchronization method———— Start-stop synchronization

Communication speed————— 2400/4800/9600/19200 bps (Selectable by keypad)

Data bit /Parity ———————- Data bit: 7 or 8, Parity: Even/Odd /No parity (Selectable by keypad) Stop bit———————————— 1 or 2 (Selectable by keypad)

Communication protocol———— Shinko protocol/Modbus ASCII/Modbus RTU (Selectable by keypad)

Number of connectable units—– Max. 31 units per host computer

Communication error detection — Parity, checksum, LRC (Modbus ASCII), CRC-16 (Modbus RTU) Data format

If this option is ordered, Set value memory external selection (SM option) cannot be ordered.

Set value memory external selection

Contact input terminal DI2 can be used for ʻSet value memory external selectionʼ or for ʻOUT/OFF external selectionʼ in [Contact input function] in Setup mode.

If ʻAuto/Manual control functionʼ is selected in [OUT/OFF key function] in Setup mode, externally Auto/Manual control can be switched. Circuit current when closed: Approx. 12 mA

If this option is ordered, Serial communication (C5 option) cannot be ordered.