Bộ điều khiển nhiệt độ 100 bước có ngõ ra SSR PCB1S00-19

Bộ điều khiển nhiệt độ 100 bước có ngõ ra SSR PCB1S00-19

– Điện áp không tiếp xúc SSR drive: 12 VDC ± 15%
– Nguồn cấp: 100 – 240 V DC
– Ngõ ra EV2 , sưởi/ làm mát OUT2, ngõ ra rơ-le
– IP66

Bộ điều khiển nhiệt độ 100 bước có ngõ ra SSR PCB1S00-19 là bộ điều khiển lập trình công nghiệp dùng để nhận tín hiệu cảm biến và điều khiển quá trình (như nhiệt độ) theo chương trình cài đặt

– Điện áp không tiếp xúc SSR drive: 12 VDC ± 15%
– Nguồn cấp: 100 – 240 V DC
– Ngõ ra EV2 , sưởi/ làm mát OUT2, ngõ ra rơ-le
Bộ điều khiển nhiệt độ 100 bước có ngõ ra SSR PCB1S00-19-detail

Bộ điều khiển nhiệt độ 100 bước có ngõ ra SSR PCB1S00-19-detail

Sản phẩm khác

Thông số kỹ thuật – Bộ điều khiển nhiệt độ 100 bước có ngõ ra SSR PCB1S00-19

Spec

Input

Input

Thermocouple	K, J, R, S, B, E, T, N, PL-II, C(W/Re5-26) External resistance: 100 max. However, B: 40 max.
RTD	Pt100, JPt100 3-wire type Allowable input lead wire resistance: 10 max. per wire
Direct current	0 to 20 mA DC, 4 to 20 mA DC Input impedance: 50 Allowable input current: 50 mA max.
DC voltage	0 to 1 V DC Input impedance: 1 M min. Allowable input voltage: 5 V DC max. Allowable signal source resistance: 2 k max.
DC voltage	0 to 5 V, 1 to 5 V, 0 to 10 V DC Input impedance: 100 k min. Allowable input voltage: 15 V DC max. Allowable signal source resistance: 100 max.

Event input
(Optional)

Input points	2 points
Circuit current when closed	Approx. 16 mA
Action	Edge action When the power is turned on, level action is engaged.

Output

Control output

Relay contact 1a	Control capacity: 3 A 250 V AC (resistive load) 1 A 250 V AC (inductive load cos=0.4) Electrical life: 100,000 cycles Minimum applicable load: 10 mA 5 V DC
Non-contact voltage (for SSR drive)	12 V DC15% Max. 40 mA (Short circuit protected)
Direct current	4 to 20 mA DC Resolution: 12000 Load resistance: Max. 550

Event output
EV1 to EV3

Relay contact
1a

Control capacity: 3 A 250 V AC (resistive load)
1 A 250 V AC (inductive load cos=0.4)
Electrical life: 100,000 cycles
Minimum applicable load: 10 mA 5 V DC

Control output OUT2
(Optional)


Relay contact 1a	Control capacity: 3 A 250 V AC (resistive load) 1 A 250 V AC (inductive load cos=0.4) Electrical life: 100,000 cycles Minimum applicable load: 10 mA 5 V DC
Non-contact voltage (for SSR drive)	12 V DC15% Max. 40 mA (Short circuit protected)
Direct current	4 to 20 mA DC Resolution: 12000 Load resistance: Max. 550

Transmission output
(Optional)

Resolution	12000
Output	4 to 20 mA DC (Load resistance: Max. 550 )
Output accuracy	Within 0.3% of Transmission output span
Response time	400 ms + Input sampling period (0%-->90%)

Insulated power output
(Optional)

Output voltage	243 V DC (When load current is 30 mA DC)
Ripple voltage	Within 200 mV DC (When load current is 30 mA DC)
Max. load current	30 mA DC

Performance

Base accuracy

At ambient temperature 23 (for a single unit mounting)

Thermocouple	Within 0.2% of each input span1 digit However, R, S inputs 0 to 200 (32 to 392): Within 6 (12) B input 0 to 300 (32 to 572): Accuracy is not guaranteed. K, J, E, T, N inputs, Less than 0 (32): Within 0.4% of input span1 digit
RTD	Within 0.1% of each input span1 digit
Direct current, DC voltage	Within 0.2% of each input span1 digit

Effect of ambient
temperature

Within 50 ppm/ of each input span

Input sampling period

125 ms

Time setting accuracy

Within 0.5% of setting time

Program Performance

Number of patterns	10 (Linkable)
Number of steps	100 (10-steps/pattern)
Number of repetitions	0 to 10000 times (Repetitions disabled when set to 0.)
Program time range	0 to 99 hours 59 minutes/step or 0 to 99 minutes 59 seconds/step (When —- is set, Fixed value control is performed using the step SV.)
Wait value	Thermocouple, RTD input without decimal point: 0 to 20% of input span DC voltage, current input: 0 to 20% of scaling span (The placement of the decimal point follows the selection.) (The Wait function is disabled when set to 0 or 0.0.)

Bộ điều khiển nhiệt độ 100 bước có ngõ ra SSR PCB1S00-19

PCB1