Đầu nối M8 male 0° A-code 3 chân IDC 7000-08325-0000000
– Đầu nối IDC đực thẳng
– M8, 3 cực.
– Tiết diện kết nối: 0,25…0,5 mm²
– IP67, IP65
– Phạm vi kẹp tối thiểu: 2,5 mm
– Phạm vi kẹp tối đa: 5 mm
Đầu nối M8 male 0° A-code 3 chân IDC 7000-08325-0000000: Đầu nối cảm biến công nghiệp của Murrelektronik, dùng để đấu nhanh cáp tín hiệu bằng công nghệ IDC (không cần tuốt dây)
– Đầu nối IDC đực thẳng
– M8, 3 cực.
– Tiết diện kết nối: 0,25…0,5 mm²
– IP67, IP65
– Phạm vi kẹp tối thiểu: 2,5 mm
– Phạm vi kẹp tối đa: 5 mm
THÔNG SỐ KỸ THUẬT – Đầu nối M8 male 0° A-code 3 chân IDC 7000-08325-0000000
Header
| Material short text | MSHL0-AC-R IDC 0,25-0,5mm² |
Side 1
| Family construction form | M8 |
| No. of poles | 3 |
| Gender | male |
| Mounting method | inserted, screwed |
| Cable outlet | straight |
| Material | PA |
| Material contact | Copper alloy |
| Degree of protection (EN IEC 60529) | IP67, IP65 |
Side 2
| Mounting method | Field-wireable |
Electrical data | Supply
| Operating voltage AC max. | 48 V |
| Operating voltage DC max. | 60 V |
| Current operating per contact max. | 4 A |
Installation
| Connection cross section min. | 0,25 mm² |
| Connection cross section max. | 0,5 mm² |
Installation | Connection
| Connection | Cut clamps IDC |
| Tightening torque | 0,4 Nm |
| Mounting set | M8 x 1 |
| Mating cycles min. | 100 |
| Wire insulation diameter min. | 1,1 mm |
| Wire insulation diameter max. | 1,55 mm |
Device protection | Electrical
| Additional condition protection degree | inserted, screwed |
| Pollution Degree | 3 |
| Overvoltage category (EN 60950-1) | II |
| Rated surge voltage | 0,8 kV |
| Insulation resistance min. | 100 mΩ |
| Material group (IEC 60664-1) | III |
Mechanical data | Material data
| Material contact carrier | TPU |
| Coating contact | gold plated |
| Locking material | Zinc die-casting |
| Coating locking | Nickeled |
| Material gasket | NBR |
Mechanical data | Mounting data
| Mounting method | Hexagonal screw, Hexagonal nut |
| Looking techniques | Schraubgewinde |
| Clamping range min. | 2,5 mm |
| Clamping range max. | 5 mm |
Environmental characteristics | Climatic
| Operating temperature min. | -25 °C |
| Operating temperature max. | 80 °C |
Important installation notes
| Note on bending radius | Attention: Observe the permissible bending radii when laying cables, as the IP protection class can be endangered by excessive bending forces. |
| Note on strain relief | Protect the connectors by suitable measures from mechanical loads, e.g. by the usage of cable ties. |
Conformity
| Product standard | EN IEC 61076-2-114 (M8) |
