Bộ điều khiển nhiệt độ 2 kênh với ngõ ra 4-20mA có truyền thông

Bộ điều khiển nhiệt độ 2 kênh với ngõ ra 4-20mA có truyền thông RS-485 WCL-13A-AA/MM, 1, C5

– Kích thước 30 x 88 x 110mm
– Điều khiển PID 2 kênh
– 2 ngõ ra relay
– Có nhiều kiểu ngõ vào: RTD, DC dòng và áp.
– Ngõ ra điều khiển 4-20 mA
– Nguồn cấp 24V AC/DC
– Có truyền thông RS-485

Bộ điều khiển nhiệt độ Shinko WCL-13A-RR/MM, 1, C5 là bộ điệu khiển nhiệt độ 2 kênh. Ngõ ra điều khiển relay

Bộ điều khiển nhiệt độ 2 kênh với ngõ ra 4-20mA có truyền thông RS-485 WCL-13A-AA/MM, 1, C5- detail

– Điều khiển PID
– 2 kênh điều khiển heating/cooling (ngõ ra relay)
– Có nhiều kiểu đầu vào (multi-input): RTD, DC dòng và áp
– Nguồn cấp 24 V AC/DC
– Có truyền thông RS-485
– Tiết kiệm không gian với kích thước chỉ 30 x 88 x 110mm

Bộ điều khiển nhiệt độ 2 kênh với ngõ ra 4-20mA có truyền thông RS-485 WCL-13A-AA/MM, 1, C5- detail

Sản phẩm tương tự

Thông số kỹ thuật – Bộ điều khiển nhiệt độ 2 kênh với ngõ ra 4-20mA có truyền thông RS-485 WCL-13A-AA/MM, 1, C5

Rating

Measurement range

Multi-range input

Input		Range
M	K	-200 to 1370	-320 to 2500
	K	-199.9 to 400.0	-199.9 to 750.0
	J	-200 to 1000	-320 to 1800
	R	0 to 1760	0 to 3200
	S	0 to 1760	0 to 3200
	B	0 to 1820	0 to 3300
	E	-200 to 800	-320 to 1500
	T	-199.9 to 400.0	-199.9 to 750.0
	N	-200 to 1300	-320 to 2300
	PL-II	0 to 1390	0 to 2500
	C(W/Re5-26)	0 to 2315	0 to 4200
	Pt100	-199.9 to 850.0	-199.9 to 999.9
	Pt100	-200 to 850	-300 to 1500
	JPt100	-199.9 to 500.0	-199.9 to 900.0
	JPt100	-200 to 500	-300 to 900
	4 to 20mA (*1)	-1999 to 9999 (*2)
	0 to 20mA (*1)
	0 to 1V
	0 to 5V
	1 to 5V
	0 to 10V

(*1): 50 shunt resistor (sold separately) should be connected externally.
(*2): Scaling and decimal point place change are possible.

Infrared thermocouple input

Input		Range
I	RD-300 series or RD-401	-50 to 500	-58 to 932

Input

Thermocouple	K, J, R, S, B, E, T, N, PL-II, C(W/Re5-26) External resistance 100 or less (However, B input: 40 or less)
RTD	Pt100, JPt100, 3-wire system Allowable input lead wire resistance (10 or less per wire
Direct current	0 to 20mA, 4 to 20mA DC Input impedance: 50 Allowable input current: 50mA or less
DC voltage	0 to 1V DC Input impedance: 1M or more Allowable input voltage: 5V DC or less Allowable signal source resistance: 2k or less
DC voltage	0 to 5V, 1 to 5V, 0 to 10V DC Input impedance: 100k or more Allowable input voltage: 15V DC or less Allowable signal source resistance: 100 or less
Infrared thermocouple	RD-300 series, RD-401

Supply voltage

100 to 240V AC 50/60Hz, 24V AC/DC 50/60Hz

Allowable fluctuation range

85 to 264V AC, 20 to 28V AC/DC

General structure

Dimensions

30x88x110mm (WxHxD, including the socket)

Mounting

DIN rail

Material

Case: Flame-resistant resin

Color

Light gray

Front panel

Membrane sheet

Indication structure

PV/SV display	CH1	7-segment Red LED display 4-digit Character size, 10×4.6mm (HxW)
PV/SV display	CH2	7-segment Red LED display 4-digit Character size, 10×4.6mm (HxW)
Action indicators	OUT(Green)	Lights when control output is ON. (CH1, CH2 individually) For DC current output type, flashes corresponding to the MV in 125ms cycles. With Timer spec, the CH2 OUT indicator lights when timer output is ON.
	EVT(Red)	Lights when any alarm is ON from Alarm, Loop break alarm (LA), Heater burnout alarm (HB). (CH1, CH2 individually)
	AT(Yellow)	Flashes while auto-tuning (AT) or auto-reset is performing. (CH1, CH2 individually)
	T/R (Yellow)	Lights during Serial communication (TX output).
	PWR (Yellow)	Lights when power is turned on.

Indication performance

Indication accuracy

Thermocouple	Within 0.2% of each input span1digit or 2 (4), whichever is greater R, S input: 0 to 200 (0 to 400): Within 6 (12) B input: 0 to 300 (0 to 600): Accuracy is not guaranteed. K, J, E, T, N input, Less than 0 (32): Within 0.4% of each input span 1digit
RTD	Within 0.1% of each input span1digit, or 1 (2), whichever is greater
DC voltage DC current	Within 0.2% of each input span1digit
Infrared thermocouple	Within 0.2% of each input span1digit or 2 (4), whichever is greater PV varies as infrared emissivity value is changed. Setting range: 0.100 to 1.000 (Default value: 0.900)

Cold junction temperature compensation accuracy

Within 1 at 0 to 50

Input sampling period

25ms, 125ms, 250ms. Selectable by keypad (Default value: 125ms)

Potentiometer input setting accuracy

Total resistance	1k to 10k
Reference voltage	1V DC
Accuracy	Same as the setting accuracy
Temperature coefficient	0.05%/
Potentiometer input sampling	Depends on Input sampling period selection.

Potentiometer input high and low limit depend on the External setting input high and low limit.

Timer specification

Time accuracy

Within 0.5% of setting time

Control performance

Setting accuracy

Same as the indication accuracy

Control action

PID control (with auto-tuning)
PI control: When derivative time is set to 0.
PD control (with auto-reset function): When integral time is set to 0
P control (with auto-reset function): When integral and derivative times are set to 0.
ON/OFF control: When the proportional band is set to 0 or 0.0.

Proportional band (P)	0 to 9999 (), 0.0 to 999.9 () (DC current, voltage input: 0.0 to 999.9%)
Integral time (I)	0 to 3600 sec
Derivative time (D)	0 to 3600 sec
Proportional cycle	1 to 120 sec
ARW	0 to 100%
Reset	100.0 () (DC current, voltage input: 1000)
ON/OFF hysteresis	0.1 to 100.0 () (DC current, voltage input: 1 to 1000)
Output high limit, low limit	0 to 100% (DC current output: -5 to 105%)
Output rate-of -change	0 to 100%

Control output

Relay contact 1a	Control capacity: 3A 250V AC (resistive load), 1A 250V AC (inductive load cos =0.4) Electrical life: 100,000 cycles
Non-contact voltage (for SSR drive)	12V DC15% Max 40mA DC (short circuit protected)
DC current	4 to 20mA DC, Load resistance: Max 550

Standard functions

Alarm

Alarm type can be selected by keypad
-High limit alarm
-Low limit alarm
-High/Low limits alarm
-High/Low limit range alarm
-Process high alarm
-Process low alarm
-High limit alarm with standby
-Low limit alarm with standby
-High/Low limits alarm with standby

Setting accuracy	Same as indication accuracy
Action	ON/OFF action
Hysteresis	Thermocouple, RTD input: 0.1 to 100.0 () DC current, voltage input: 1 to 1000
Output	No output (Read with the status flag in Serial communication.)
Alarm delay timer	0 to 9999 sec

Loop break alarm

Detects heater burnout, sensor burnout, actuator trouble.

Loop break alarm time	0 to 200 minute
Loop break alarm span	Thermocouple, RTD input: 0 to 150 () or 0.0 to 150.0 () DC current, voltage input: 0 to 1500
Output	No output (Read with the status flag in Serial communication.)

SV ramp function

When the SV is adjusted, it approaches the new SV by the preset rate-of-change (/min, /min)
When the power is turned on, the control starts from the PV and approaches the SV by the rate-of-change.

Auto/Manual control switching

Auto/Manual control can be switched by keypad.
If control action is switched from automatic to manual and vice versa, balanceless-bumpless function works to prevent sudden MV change.
If control action is switched to manual, the manual MV is indicated on the display. (CHx display flashes.)
When power is turned on, control action starts from its previous controller status (last shutdown).

Timer spec

Selects either Control timer or Delay timer function.
–Control timer:
Timer starts when CH1 input exceeds Control timer start temperature.
After Control timer setting time has elapsed, control (for DC current output, output low limit) and alarm action will stop.
–Delay timer:
When DI input is ON (Closed), the timer starts.
Timer output turns ON after ON delay timer time has passed.
Timer output turns OFF after OFF delay timer time has passed.

Cascade control
(Block function)

To control one process, 2 inputs [CH2 as a master (1st-order controller), and CH1 as a slave (2nd-order controller)] are used for more advanced control.
MV is calculated from PV and SV of the master (CH2), and is used as SV of the slave (CH1), with which CH1 control computation is carried out, then outputs from CH1 control output.
[CH2 control output will be OFF (0mA for DC current output) or OUT2 (Cooling output) for Heating/Cooling control.] MV (0 to 100%) of the master (CH2) corresponds to the SV (External setting low limit to External setting high limit) of the slave (CH1).

Heating/Cooling control output (Block function)

This is 1ch Heating/Cooling control output spec. CH1 will be Heating output (OUT1) and CH2 will be Cooling output (OUT2), followed by control performance.

OUT2 proportional band (P)	0.0 to 10.0 times OUT1 proportional band (ON/OFF control when set to 0.0.)
Integral time (I)	Same as that of OUT1
Derivative time (D)	Same as that of OUT1
OUT2 proportional cycle	1 to 120sec
ARW	Same as that of OUT1
Overlap/Dead band	Thermocouple, RTD input: -100.0 to 100.0 () DC current, voltage input: -1000 to 1000
OUT2 ON/OFF hysteresis	0.1 to 100.0 () (DC current, voltage input: 1 to 1000)
OUT2 high limit, OUT2 low limit	0 to 100% (DC current output: -5 to 105%)
OUT2 action mode	Air cooling (linear characteristic), Oil cooling (1.5th power of the linear characteristic), Water cooling (2nd power of the linear characteristic)

Output

Relay contact 1a	Control capacity: 3A 250V AC (resistive load) Electrical life: 100,000 cycles
Non-contact voltage (for SSR drive)	12V DC15%, Max 40mA DC (short circuit protected)
DC current	4 to 20mA DC, Load resistance: Max 600

External setting input
(Block function)

External analog signal will become the SV.
Control desired value (SV) adds remote bias value to the External setting input value.
As a setting signal, specify any DC range during input type selection via console software.

Setting signal	DC current: 4 to 20mA or 0 to 20mA DC DC voltage: 1 to 5V or 0 to 1V DC
Allowable input	DC current: 50mA DC or less DC voltage (0 to 1V): 5V DC or less DC voltage (1 to 5V): 10V DC or less
Input impedance	DC current: 50 [Externally connect a shunt resistor (sold separately).] DC voltage: 100k
Input sampling period	Depends on Input sampling period selection.

Transmission output (Block function)

Converting any value (PV, SV or MV) to analog signal every input sampling period, outputs the value in current.
To use Transmission output, specify ‘Current’ for CH2 control output.

Resolution	1/10000
Current	4 to 20mA DC (load resistance Max 550)
Output accuracy	Within 0.3% of Transmission output span

CH1 PV difference (CH1-CH2) input
(Block function)

Temperature difference between CH1 and CH2 (CH1-CH2) will be the input value for CH1, and control is performed using this value.
PV = (CH1 PV – CH2 PV)
Set values such as input type, scaling and PV filter time constant can be individually set to CH1 and CH2.
However, if CH ranges differ from each other, indication and difference depend on the reference channel.

CH1 PV addition (CH1+CH2) input
(Block function)

Addition value of CH1 and CH2 will be the input value for CH1, and control is performed using this value.
PV = (CH1 PV + CH2 PV)
Set values such as input type, scaling and PV filter time constant can be individually set to CH1 and CH2.
However, if CH ranges differ from each other, indication and addition depend on the reference channel.

CH2 PV difference (CH2-CH1) input
(Block function)

Temperature difference between CH1 and CH2 (CH2-CH1) will be the input value for CH2, and control for CH2 is performed using this value.
PV = (CH2PV – CH1PV)
Set values such as input type, scaling and PV filter time constant can be individually set to CH1 and CH2.
However, if CH ranges differ from each other, indication and difference depend on the reference channel.

CH2 PV addition (CH1+CH2) input
(Block function)

Addition value of CH1 and CH2 will be the input value for CH2, and control is performed using this value.
PV = (CH1 PV + CH2 PV)
Set values such as input type, scaling and PV filter time constant can be individually set to CH1 and CH2.
However, if CH ranges differ from each other, indication and addition depend on the reference channel.

Attached functions

Sensor correction, set value lock, automatic cold junction temperature compensation, burnout, console communication, block selection function, power failure countermeasure, self-diagnosis, warm-up indication, display-off function, auto-light function

Optional functions

Heater burnout alarm (Sensor burnout alarm included)

Monitors heater current with CT (current transformer), and detects burnout.
This option cannot be added to DC current output type.

Rated current	Single-phase 20A, 3-phase 20A, Single-phase 100A, 3-phase 100A (Must be specified) Single-phase: Detects with CT1 (CT input for CH1) and CT3 (CT input for CH2). 3-phase: Detects with CT1 & CT2 (CT input for CH1), and CT3 & CT4 (CT input for CH2).
Setting range	0.0 to 20.0A (For 20A. Disabled when set to 0.0.) 0.0 to 100.0A (For 100A. Disabled when set to 0.0)
Setting accuracy	5% of the rated current
Action point	Set value
Action	ON/OFF action
Output	No output (Read with the status flag in Serial communication.)

Serial communication

The following operations can be carried out from an external computer.
(1) Reading and setting of the SV, PID values and various set values
(2) Reading of the PV and action status
(3) Function change

Communication line

EIA RS-485

Communication method

Half-duplex communication

Synchronization method

Start-stop synchronization

Communication speed

9600, 19200, 38400bps, Selectable by keypad

Data bit/Parity

Data bit: 7 or 8
Parity: Even, Odd, No parity, Selectable by keypad

Stop bit

1 or 2, Selectable by keypad

Data format

Communication protocol	Shinko	Modbus ASCII	Modbus RTU
Start bit	1	1	1
Data bit	7	7 or 8	8
Parity	Yes (Even)	Yes (Even, Odd), No parity	Yes (Even, Odd), No parity
Stop bit	1	1 or 2	1 or 2

Communication protocol

Shinko protocol, Modbus (ASCII mode or RTU mode), Selectable by keypad

Insulation, dielectric strength

Insulation resistance	10M or more, at 500V DC
Dielectric strength	1.5kV AC for 1 minute Between power terminal and ground Between input terminal and ground Between input terminal and power terminal

Other

Power consumption

Approx. 9VA

Ambient temperature

0 to 50

Ambient humidity

35 to 85%RH (Non-condensing)

Weight

Approx. 200g (including the socket)

Accessories included

Instruction manual, 1 copy

Accessories
sold separately

Socket	ASK-001-1 (Finger-safe, Ring terminals unusable)
Socket	ASK-002-1 (Ring terminals usable)
Shunt resistor	50 (for DC current input)
CT	CTL-6S (for Heater burnout alarm 20A) (*1)
CT	CTL-12-S36-10L1U (for Heater burnout alarm 100A) (*1)
Connector harness	3m (for Heater burnout alarm) (*2)
Communication cable	CMB-001 [For console software SWS-WCL01M)]

(*1) For 3-phase, 2 pieces are needed for each channel.
(*2) For 3-phase, 2 lengths are needed for each channel.

Catalog Bộ điều khiển nhiệt độ shinko WCL-13A